EU Directive,ICNIRP Guidelines and Polish Legislation on Electromagnetic Fields

This review describes the general provisions of and the philosophy behind European Directive 2004/40/EC and ICNIRP (International Commission on Non-Ionizing Radiation Protection) guidelines. As an example of national legislation on the protection of workers against excessive electromagnetic field exposure, regulations established in Poland are summarized. The problems of a practical implementation of the Directive’s provisions are discussed.     

Persistent organochlorine pesticides in internal organs of coypu,Myocastor coypus

A highly selective and sensitive method based on gas chromatography-tandem mass spectrometry (GC-MS/MS) to identify and quantify persistent organochlorine pesticides, (18 compounds including primary compounds and metabolites), in animal internal organs (kidneys, liver, and brain) has been developed. Tandem mass spectrometric conditions were individually optimized for each target compound in Multiple Reaction Monitoring (MRM) mode to obtain maximum sensitivity. Prior to instrumental analysis, a sample preparation method based on matrix solid phase dispersion (MSPD) followed by acidic digestion with sulfuric acid to reduce matrix co-extractives was employed. Analyses of real samples were carried out on coypus (Myocastor coypus) from the autumn slaughter of 19 animals. In the analyzed samples, three of the target compounds, namely DDE-pp′ (DDT metabolite), HCB and lindane, were detected. Their concentration levels fell in the ranges of 0.003–0.007, 0.003–0.025, and 0.003–0.021 mg kg^?1 (0.005, 0.010, and 0.010 mg kg^?1 on average) in the case of DDE-pp′, HCB and lindane, respectively. Although low quantities of organochlorine pesticides do not pose an immediate danger to consumers' health, they should be of public health concern considering long-term, low-dose exposure.     

Occupational risk from static magnetic fields of MRI scanners

The health care staff operating magnetic resonance imaging (MRI) scanners are exposed to static magnetic field of significant spatial heterogenity and high level of flux density—usually existing permanently during the shift. The personnel can also be exposed to pulses of magnetic field of high rate of rise/fall, so-called gradient fields, which exist only during examination of patients. The level of workers’ exposure depends both on the type of the magnet and on the ergonomical characteristic of design of the particular MRI scanner. This paper presents the current state of the art on occupational exposure to static magnetic field health effects, gaps in scientific data, MRI workers’ exposure characteristics, research needs, and suggestions for the exposure assessment protocol for future investigations.     

Practical aspects of occupational EMF exposure assessment

Electromagnetic fields exposure assessment methodology is briefly presented. The basic problems defined for the practical use of electromagnetic fields measurements and numerical calculations carried out for workers exposure assessment in real occupational situations are discussed. The examples of data from real workplace are presented, focusing: spatial distribution of electromagnetic fields affecting worker’s body, complex characteristics of the frequency content, workers activities/moving in the workplace, field impedance, etc. The situation when the use of calculations is required is discussed. The basic requirements for workers exposure assessment protocols are presented. The possible range of the use of internal and external measures of exposure level is also discussed.     

Permeability of Organic Solvents Through Two-Layer Safety Gloves Determined by a Gravimetric Method

Organic solvents are harmful to humans, and many of them are recognized as carcinogens. Therefore, it is necessary to protect hands from contact with them. Most methods for testing solvent resistance of gloves use gas chromatography. However, these methods are expensive and so complex that they present application problems for most glove producers and users. A simple gravimetric method to test solvent resistance o f gloves was developed. It was tested by measuring the permeability of organic solvents such as white spirit, acetone, isopropyl alcohol, benzene, p-xylene, and trichloroethylene through gloves made of natural rubber, polyvinyl chloride, neoprene, perbunan, polyvinyl alcohol, and two-layer gloves made of natural rubber and neoprene. This method proved to be a simple, economical, and reliable way to examine glove permeability.     

Classification of the Substances on the Basis of the Acute-Toxic-Class Method (ATC)

The acute-toxic-class method (ATC) is an alternative to the classical LD₅₀ test. Four substances were tested with an ATC testing procedure. The results were compared with LD₅₀ data obtained from the literature. Great importance was attached to the observations of toxic signs following administration. The results of this study have shown that the ATC method allows allocation to toxicity classes in the same manner as on the basis of the classical LD₅₀ tests. The ATC method uses fewer animals and yields the same information on toxic signs. Introducing the ATC method into the quality system allows estimating the acute oral toxicity of chemicals according to the Organisation for Economic Cooperation and Development (OECD; OECD, 1992, 1996).     

Historical deforestation as a cause of alluviation in small valleys, subcarpathian loess plateau, Poland

The undulating loess Kanczuga Plateau, 250–270 m a.s.l., is located in the temperate climatic zone of Central Europe, within the northern foreland of the Carpathians. It is dissected by a network of valleys 30–60 m deep, infilled with several metres of complex minerogenic and organic deposits which started to accumulate during the early Holocene. The southern side of one of these valleys is dissected by several dry valleys. The mouth sections of these valleys have buried surface comprising peat and/or organic silts, overlain by sandy–silty alluvium. ¹⁴C dates indicate that the alluviation of these valley floors, which proceeded from the headwaters to the mouth sections, began in the 1100 ad. The gradual intensification of soil erosion in the upper part of the catchment and associated sedimentation probably encompassed only a few centuries, with greatest alluviation during the Little Ice Age. This plateau, which is under the influence of more continental climatic conditions than the low-mountain and upland regions of Western Europe, features more climatic contrasts. Here environmental changes triggered by land use were superimposed on climatic change. The most intensive processes of soil erosion and sediment transfer as well as alluviation, coincided with the first phase of cooling during the Little Ice Age. It was the final stage of the intensification of these processes, probably more intensive than its initial phase in the eleventh century, caused primarily by deforestation resulting from the development of agriculture.     

3D printing filament as a second life of waste plastics—a review

In recent times, the issue of plastic recycling has become one of the leading issues of environmental protection and waste management. Polymer materials have been found an application in many areas of daily life and industry. Along with their extended use, the problem of plastic wastes appeared because, after withdrawal from use, they became persistent and noxious wastes. The possibility of reusing polymeric materials gives a possibility of valorization—a second life—and enables effective waste utilization to obtain consumable products. The 3D printing market is a well-growing sector. Printable filaments can be made from a variety of thermoplastic materials, including those from recycling. This paper focuses on a review of the available literature on the production of filaments for 3D printers from recycled polymers as the alternative to present approach of central selective collection of plastics. The possibility of recycling of basic thermoplastic materials and the impact of processing on their physicochemical and mechanical properties were verified (Lanzotti et al. 2019). In addition, commercially available filaments produced from recycled materials and devices which allow self-production of filaments to 3D printing from plastic waste were reviewed.